Test the hand brakes to make sure that they work correctly for both the front and back tire. You should have two light reflectors, two pedals, the bike seat and post, as well as the quick release lever to adjust the seat, some of these items are located in a small cardboard box that comes with the set. First, slide the front reflector light onto the handlebars and tighten it up using your Philips head screwdriver. Proceed to slide the handlebars onto the bike’s body, it should slide down without any problems. If it gets stuck, adjust the rotating screw at the bottom of the handlebar so that it aligns correctly with the bike’s body and slide it in place. Do both the screw that connects to the body and the other top screw at the top of the handlebars.
It is an aluminum frame and the tag that was attached to the bike says that it can hold about 275 lbs or so. I was a bit surprised by this because the manufacturer should have sent us the part since the bike was just ordered brand new and we had the order number and receipt. For a product that would have cost the company a minimum of $10 to ship out, I did find it a bit frustrating that their customer service was so poor and we ended up having to pay for the replacement ourselves. The next problem is that the bike seat is hard and uncomfortable, if you only ride short distances it isn’t a problem, but if you do between 2 through 5 miles you will start to feel it. The handlebars sometimes wobble and slide out-of-place, not at the base where it connects to the body, but literally at the center “T” joint at the top near where your hands are, it will slip out-of-place and slide around. I have tightened it a few times and it now finally stays in place, but it can be dangerous when it randomly slides over while riding.
The seat post simply slides in place, but first you should slide the light reflector on it and screw it in place. There should be a back quick release clamp that will hold the seat in place that attaches to the seat post, simply grab hold of the lever, clamp it down, and pull it tight to hold the bike seat in place. The basic rule of thumb is that the bike seat should be almost equal to the height of your waist, adjust the seat accordingly so that it is comfortable. Adjust the front brake pads by pulling the silver wire tight and holding it in place, then tighten the screw back up- You may need an extra pair of hands to do it correctly. You can tighten the tire’s nuts and the front brake’s cap by using an adjustable wrench. It loses three points for the small defects and bad customer service from the manufacturer and seller.
For a product to be returned under our policy, that product must be in a resalable condition unless faulty or otherwise defective. It’s this policy that hyper bike provides you peace of mind while shopping at The Warehouse. Usually the order will be processed and ready for shipping within 1-2 business days.
Additionally make sure your User-Agent is not empty and is something unique and descriptive and try again. If you’re supplying an alternate User-Agent string,
try changing back to default as that can sometimes result in a block. Designed specifically for Time Trial and Triathlon, Corsa PRO Speed promises to revolutionize the racing experience of pro riders and performance-oriented amateur riders. The instructions were not completely helpful for assembling the bike because they were basic and very general, but overall I found it easy to do and I had the entire thing setup in about an hour or so. You can click the above link for detail instructions on how to build this specific bike yourself and all the tools you will need to do so. Proceed to locate the front brake’s screw, it is a silver cap that is connected to a small silver wire on the right side of the brake pad.
The authentic Hyper graphics complete the look and give this 20″ boys’ bike a stylish appearance. The Hyper Havoc FS mountain bike is 26″ in size, it is a 21 speed mountain bike, with Shimono gear shifters. Before I get into all the cons with the bike, I will first tell about the pros. The most obvious pro is the price, this bike is very cheap and affordable for what you get in the box and for most purposes of daily commutes to the store or to work, it will do perfectly.
The bike gears and peddles are slightly stiff, but I am sure it will loosen up with a bit of oiling and riding. I would recommend this bike if you are on a budget and need basic transportation for getting around because it does the job and serves its purpose. As far as cheap mountain bikes go, overall the Havoc Hyper FS mountain bike isn’t really all that bad. Use your 5mm hex key to adjust the screw at the top of the brake levers to rotate them around and set them in place. If your handlebars are on backwards this screw will be at the bottom of the brake lever. Make sure that they are comfortable and your wrists are not straining to use them.